Purchase 1000hp Extreme Duty Race Axles, C Black Series

SKU: 01-156-01037-4
1000hp Extreme Duty Race Axles, C Black Series
Power gain Up To
+0 HP

Torque gain Up To
+0 TQ

Advertised gains are estimates of HP and Torque “at the engine” calculated from gains as measured on a Dynojet Dynamometer in ideal conditions and typically show the largest possible change. Actual gains are dependent on the following: Learn More about Crank HP Vs Wheel HP

Model – Manufacturers use the same engine in multiple model vehicles and often times they are in a different state of tune, for example: 2008 C63 and a 2008 CLK Black Series. Both have the same engine, but the C63 has 451hp while the CLK63 has 500hp. Naturally the C63 will show more gains as it starts at a lower level.

Model Year – Similar to above, as time progresses, Manufacturers tend to slightly increase power output via software from one year to the next or offer “Performance Packages” with increased power. The engines remain largely unaltered and as a result, final tuned output remains the same, while the gains are lower as the starting point is now higher.

Fuel – Fuel quality is HIGHLY important with performance vehicles. Low quality and/or low octane fuel will greatly impact engine output and potentially even engine health. Top tier brand premium fuels should always be used to achieve the best results possible.

Drivetrain – All wheel drive has higher drivetrain losses than rear wheel drive. This results in lower numbers when testing on a chassis dyno. Wheel/tire size and weight will also impact chassis dyno results

Weather/Conditions – Temperature, humidity, altitude, and air density all impact engine performance. Heat, high humidity, and thin air will all work towards reducing engine output

Engine Health – Higher miles tends to result in increased build up and lower compression which can and will impact engine output. Properly maintained engines will have better performance than abused or neglected engines.

Supporting modifications – The highest power levels require supporting modifications. Depending on the engine, this could mean forged internals, built transmission, upgraded fuel system, 110+ octane race fuel, etc.
Please confirm:
NOT LEGAL FOR SALE OR USE ON POLLUTION CONTROLLED MOTOR VEHICLES
Learn why

Confirmation
Please confirm that you are not installing this product within the United States.

This policy only applies to installers and/or users who are in the United States, customers who reside in other countries should act in accordance with their local laws and regulations.

Some Weistec Engineering performance upgrades may solely be used on vehicles in sanctioned competition which may never be used upon a public road or highway, unless permitted by specific regulatory exemptions (such as a CARB E.O.). For state specific details please visit the following website. http://www.semasan.com/emissions

It is the responsibility of the installer and/or user of the product to ensure that it is used in compliance with all applicable laws and regulations. If a product was purchased in error, do not install and/or use it. The purchaser must arrange to return the product(s) for a full refund.

All performance modifications and installations are at the customer’s own risk. Weistec Engineering holds no responsibility either implied or otherwise for mechanical, electrical or other failure when using any aftermarket performance products.
$2,299.00 $2,299.00
Install instructions
Prop 65 warning

Warning
This product can expose you to chemicals including carbon black, silica - crystalline, formaldehyde, and lead which are known to the State of California to cause cancer, and lead, which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Product details

Manufacturer

Weistec

Vehicle application

year	make	model	trim	engine
2014	Mercedes-Benz	C63 AMG	Black Series (C204)	NA 6.2L V8 (M156)
2013	Mercedes-Benz	C63 AMG	Black Series (C204)	NA 6.2L V8 (M156)

Instructions

Install instructions

Product Description

CV axles are responsible for transferring torque and power from the differential to the wheels in a vehicle with independent suspension. The CV axles allow for power transfer through flexible CV joints. These joints make it possible to have driven wheels with independent suspensions.

The factory CV axles were designed to handle factory power levels and typical driving scenarios. The availability of performance increasing parts, such as our M156 Supercharger system, as well as repeated trips to the drag strip and track push the factory axles beyond their intended limits. Our CV axles are built to withstand 1000hp, more than enough to repeatedly handle the roughest of drag and road racing events.

1000HP rating
Larger Diameter Axle Bar
Improved CV Joint Housing and Internals
Direct replacement for factory axles

1000hp Extreme Duty Race Axles, C Black Series

Power gain Up To

Torque gain Up To

Product Description